HumiSeal 1C63 Description
- HumiSeal 1C63 is a UV/RTV curing, oxime-type cure silicone conformal coating which provides excellent moisture and environmental protection for printed circuit assemblies.
- HumiSeal 1C63 is a non-corrosive, single component coating which will cure upon exposure to either a UV light source or atmospheric moisture at ambient or elevated temperatures.
- The material is tack-free after exposure to UV light.
- A secondary moisture cure will cure unexposed areas of the coating within 24 hours at ambient temperature, 50% relative humidity.
- HumiSeal 1C63 is self-leveling, with excellent weathering resistance.
Technical data of HumiSeal 1C63
Property | Value |
---|---|
Density, per ASTM D1475 | 1.04 +/- 0.06 g/cm³ |
Viscosity, per Fed-Std-141, Meth. 4287 | 3500 ± 1500 centipoise |
VOC | < 50 grams/liter |
Room Temperature Skin Over time, 1/8” thickness | 60 minutes |
Recommended UV Cure | See curing section below |
Secondary Cure, for shadow areas | 24 hrs @ RT or 20 min @ 76°C |
Time Required to Reach Optimum Properties, 1/8” thickness | 7 days |
Recommended Stripper | HumiSeal® Stripper 1090 |
Shelf Life at Room Temperature, DOM | 6 months |
Glass Transition Temperature - DSC | < -90°C |
Tensile Strength, per ASTM D412 | 100 psi |
Elongation, per ASTM D412 | 100% |
Thermal Shock, 50 cycles per MIL-I-46058C | -65°C to 200°C |
Volume Resistivity, per ASTM D257 | 7.97 x10^14 ohm-cm |
Surface Resistivity, per ASTM D257 | 6.26 x10^17 ohms per square |
Shore Hardness, A, per ASTM D2240 | 15 |
Flammability, per UL94 | V-1 |
Dielectric Withstand Voltage, per MIL-I-46058C | >1500 volts |
Insulation Resistance, per MIL-I-46058C | 1.1 x 10^12 ohms (1.1 TΩ) |
Moisture Insulation Resistance, per MIL-I-46058C | 1.1x 10^10 ohms |
This table summarizes the various properties and specifications of the material. If you have any further questions or need more information, feel free to ask!
Application of HumiSeal 1C63
- Solvents or other thinners should not be mixed with 1C63.
- Conformal coatings can be successfully applied to substrates that have been cleaned prior to coating and also to substrates assembled with low residue, “no clean” assembly materials.
- Users should perform adequate testing to confirm compatibility between the conformal coating and their particular assembly materials, process conditions and cleanliness level.
- 1C63 is designed for application without additional thinning.
Brushing
- Uniformity of the film depends on component density and operator's technique.
- HumiSeal 1C63 may be applied by brush.
- The actual uniformity of the finished coating will depend on component density and operator technique.
- Brushes may be cleaned promptly using solvent.
Dispensing
- HumiSeal 1C63 may be applied via standard selective coating equipment such as jet or atomized spray as well as needle valves.
- The source air used for spraying must be dry to prevent premature curing by the effective secondary cure mechanism.
- An inert gas such as nitrogen or argon is highly recommended.
- The dispensing should be done with adequate ventilation so that vapour and mist are carried away the operator.
Curing
- HumiSeal 1C63 is a highly cross linked coating.
- In order to achieve maximum cross linking density, the product must be exposed to the correct spectral output.
HumiSeal 1C63 Application notes
Storage
- HumiSeal 1C63 is photosensitive. The product should not be exposed to direct sunlight or full spectrum fluorescent lighting.
- HumiSeal 1C63 should be stored at 27°C or below in tightly closed containers in a dry place away direct sunlight.
- HumiSeal 1C63 is also a moisture sensitive material. If coating is partially used, the container should be purged with dry nitrogen or argon prior to resealing to protect the remainder of the coating.
- Prior to use, allow the product to equilibrate for 24 hours at room temperature.
Caution
- Application of HumiSeal Conformal Coatings should be carried out in accordance with local and National Health and Safety regulation.
- Use only in well-ventilated areas to avoid inhalation of vapours or spray. Avoid contact with skin and eyes.
Where to buy HumiSeal 1C63 ?
As an authorized distributor, Hicotech provides genuine HumiSeal 1C63 and various other industrial products including lubricating oils, greases, chemicals, and more. We offer consultation services and competitive pricing. Please don't hesitate to contact us for further information.
In addition, we also distribute other product categories such as:
- Industrial chemicals
- Cleaning Chemicals
- Encapsulants
- SMT equipment
- Conformal coatings
- Industrial Accessories
Contact Information:
Hotline/Zalo. 094 526 1931
Website. Hicotech.com.vn
Email: Sale@hicotech.com.vn
Xem thêm
Tin tức mới nhất
Có 0 đánh giá về HumiSeal 1C63
5
0 đánh giá
4
0 đánh giá
3
0 đánh giá
2
0 đánh giá
1
0 đánh giá
X
Có 0 bình luận, đánh giá về HumiSeal 1C63
TVQuản trị viênQuản trị viên